Cambria Roofing Nationwide

Cambria Roofing: The West Palm Beach Owner’s Guide

We stock and install Cambria-compatible roofing components in West Palm Beach, with typical repairs running $400-$1,800 and full replacements at $8,000-$20,000 depending on substrate condition and square footage. Most Cambria parts are available same-day through our supplier network, and we carry common flashings, fasteners, and membrane sections on our trucks. Homeowners usually discover a problem during our summer storm season, when wind-driven rain finds its way past a lifted ridge cap or cracked tile, or when they spot granules collecting in the gutter after a routine downpour.

Call (561) 475-3903

Which Cambria Models This Applies To

Cambria’s roofing line is narrower than their countertop catalog, which is what most West Palm Beach homeowners know them for. The Cambria Roof System was produced in two series: the CRS-2000 (2008-2016) and the CRS-3000 (2017-2022), both manufactured under license by a third-party roofing partner. The CRS-2000 used a 24-gauge galvanized steel substrate with a stone-coated finish; the CRS-3000 shifted to 26-gauge aluminum with the same finish for salt-air resistance.

To identify your series, check the underside of any lifted tile or the interior face of the ridge vent, where a stamped date code and “CRS-2K” or “CRS-3K” appears. The fastener pattern differs between series: CRS-2000 used a 6-inch center-to-center screw line, while CRS-3000 moved to 8-inch centers with a hidden clip system. We source OEM Cambria-specified components where the series is still supported, and for discontinued CRS-2000 inventory, we match to stone-coated steel from Decra or Metro that meets the same Class A fire rating and 120-mph wind uplift. The color match is never perfect on a 15-year-old roof, so we typically replace an entire slope rather than spot-patch and leave you with a checkerboard.

Signs Your Cambria Roofing Is Failing

• Granule loss in gutters or downspout outlets. The stone-coated finish on Cambria tiles is bonded with an acrylic base coat that degrades faster in West Palm Beach’s UV exposure than the manufacturer originally spec’d. Once the granules shed, the underlying metal is exposed to salt air and begins pitting within two to three seasons.
• Lifted or cupped tiles at the ridge or hip lines. The CRS-2000 relied on foam adhesive strips that turn brittle after a decade of Florida heat cycles. When the bond fails, tiles lift and create a channel for wind-driven rain; we’ve traced interior ceiling stains directly to this failure pattern on homes along Flagler Drive.
• Rust streaks running from fastener heads or overlapping edges. Even “galvanized” steel has its limits in coastal humidity. The CRS-2000’s cut edges were not always factory-sealed, and once oxidation starts at a fastener hole, it spreads under the finish in a way that looks cosmetic from the ground but is structural up close.
• Daylight visible through the roof deck from inside the attic. This means a tile is missing, cracked, or the underlayment has degraded. Cambria’s system used a synthetic underlayment rated for 25 years, but in unvented attics in West Palm Beach, we’ve seen it become brittle in 14 to 16 years.
• Sagging or soft spots when walking the roof. The metal tiles themselves may be intact, but the plywood or OSB deck beneath has taken moisture and begun delaminating. This is common where CRS-2000 adhesive failure went unaddressed for multiple rainy seasons.

Before

After

Replacement Cost & What’s Included

The range within each tier depends on three factors: deck condition (we find soft plywood on roughly 30% of CRS-2000 tear-offs), access complexity (steep pitches or tight setbacks in downtown West Palm Beach add labor hours), and whether the original fasteners were installed with proper corrosion-resistant specs. Under Clause 1 of The Haven Standard, you get a written line-item quote before any work starts, and no change order proceeds without your signature. Our 365-Day Done Right Promise covers the workmanship; the materials carry the manufacturer’s warranty, which we register for you and document in your project binder.

DIY or Call Us?

There is one thing a homeowner can safely check: from the ground, use binoculars to scan for missing tiles, lifted edges, or rust streaks. Note the location and take a photo. That information helps us bring the right parts on the first trip.

Everything else belongs to a trained crew. Walking a stone-coated steel roof requires knowing where to step to avoid creasing the tile profile; the metal is thin enough to dent under a misplaced boot. Cutting tiles to fit around vents or chimneys creates sharp edges that will slice through gloves. And the real risk is not the fall itself but what you land on: West Palm Beach’s single-story homes often have concrete pavers or pool decks directly below the eaves. We carry liability insurance and workers’ comp for a reason. If you’ve spotted something that doesn’t look right, call (561) 475-3903 and we’ll schedule a no-charge inspection with a documented photo record you can review before deciding on any work.

FAQs