Atlas Kitchen Remodeling Nationwide

Atlas Kitchen Remodeling: The West Palm Beach Owner’s Guide

Atlas kitchen remodeling in West Palm Beach typically runs $14,000-$45,000 for a full project, with cabinet installation, countertop replacement, and island reconfiguration available as standalone services starting at $4,000, $2,000, and $3,000 respectively. We stock Atlas-compatible cabinet hardware, drawer glide systems, and soft-close hinge assemblies on our West Palm Beach trucks, and most part replacements are completed same-day once we verify your model series. Most homeowners realize something’s off when a drawer starts sagging or a cabinet door won’t stay aligned - the hardware has worn past its tolerance, and the fix is usually a matched part swap, not a full cabinet replacement.

Call (561) 475-3903

Which Atlas Models This Applies To

Atlas produces three kitchen cabinet lines relevant to West Palm Beach homes: the Builder Series (entry-level framed construction, common in 2015-2020 production builds near Wellington and Royal Palm Beach), the Designer Series (semi-custom with ¾-inch plywood boxes and dovetailed drawers), and the Estate Series (full custom with hardwood face frames and Blum undermount hardware). The part you need depends on which series is installed in your kitchen. Builder Series uses a 22-inch side-mount ball-bearing glide with a 75-pound rating; Designer and Estate both spec Blum Tandem plus Blumotion, but the Estate line adds a heavier 120-pound soft-close slide for pantry pullouts.

To identify your series, check the inside edge of the drawer box for a stamped date code and series mark, or look for the Blum logo on the glide mechanism itself. The OEM part number is your surest match, but we’ve found that quality aftermarket equivalents from Knape & Vogt or Rev-A-Shelf perform identically in West Palm Beach’s humidity and cost 15-20 percent less. One compatibility gotcha: Atlas switched from 21-inch to 22-inch standard depths in 2018, so a pre-2018 kitchen needs exact measurement before we order. We carry both sizes on our West Palm Beach trucks to avoid a second trip.

Signs Your Atlas Kitchen Remodeling Is Failing

• Drawer sagging or binding when loaded. The ball bearings in the glide mechanism have worn flat spots, or the epoxy coating on the steel rail has corroded in the humid West Palm Beach air. The drawer box then rides cockeyed, stressing the front joint until it loosens.
• Cabinet door won’t stay closed or slams shut. The Blumotion soft-close cylinder has lost hydraulic pressure, or the hinge cup has wallowed out its 35mm bore in the particleboard door. This is the most common call we get in waterfront homes near Flagler Drive, where salt air accelerates the deterioration.
• Lazy Susan or corner unit catching mid-rotation. The polymer bearing ring has flattened or cracked, or the center shaft has bent from uneven loading. Atlas corner units use a specific 28-inch diameter ring that generic replacements don’t fit - we’ve learned that one the hard way on a job in El Cid.
• Pull-out pantry off-track or tilting forward. The bottom-mount bracket has cracked where it screws into the cabinet floor, usually from repeated overloading beyond the 100-pound spec. The fix is a reinforced bracket plus redistribution of stored weight.
• Countertop seam opening or laminate bubbling near the sink. The substrate has absorbed moisture through a failed caulk joint, or the adhesive layer has degraded in the heat. Atlas countertops are sourced separately from the cabinet boxes, so the repair protocol depends on whether it’s a postformed laminate, solid surface, or stone installation.

Before

After

Replacement Cost & What’s Included

What drives the range: part grade (OEM Blum versus quality aftermarket), accessibility (a corner base cabinet takes longer than a top drawer), and what we find once we’re inside. If the drawer box itself is delaminating, that’s a separate conversation - and under Clause 1 of the Haven Standard, we put that in writing before we proceed. No surprise, no change order without your signature.

DIY or Call Us?

There’s a short list of checks any homeowner can make safely. Verify the drawer isn’t simply overfilled past its weight rating. Tighten the visible screws on the glide face bracket with a Phillips head - not a power driver, which strips the particleboard. Check that nothing has wedged in the glide track: a utensil, a crumb buildup, a desiccated lemon from 2019.

Where DIY goes wrong: the 35mm hinge bore in an Atlas cabinet door is a precision fit, and a hand drill without a depth stop blows through the face or cants the cup. Drawer glide removal requires supporting the box while you release two locking levers simultaneously - drop it, and the corner joint splits. We’ve replaced more homeowner-damaged drawer boxes than failed glide sets in West Palm Beach. The hardware itself isn’t dangerous, but the cabinet it’s attached to is expensive. Call (561) 475-3903 and we’ll verify the part, match it, and install it with the alignment tools we carry. The estimate is free, and the price we write is the price you pay.

FAQs