Atlas Windows & Doors Nationwide

Atlas Windows & Doors: The West Palm Beach Owner’s Guide

We stock and install Atlas-compatible windows and doors across West Palm Beach, with most replacement units running $4,500-$15,000 for a full window replacement and $8,000-$25,000 for impact-rated installations, depending on opening count and series. Atlas parts we keep on hand include balances, locks, tilt latches, and weatherstrip kits for same-day service on most service calls. Most West Palm Beach owners discover a problem when the sash won’t stay up on a humid morning, or when they feel the Gulf Stream breeze through a frame that used to seal tight.

Call (561) 475-3903

Which Atlas Models This Applies To

Atlas manufactures several residential series, and the part you need depends on the age and line. The Builder Series (2008-2018) used a 5/8-inch coil balance with a stamped steel bracket that Atlas phased out; the current Pro Series and Signature Series run a 3/4-inch constant-force balance with a die-cast zinc bracket. The mounting hole spacing differs by 1/4 inch, so a Pro Series balance will not retrofit to a Builder Series sash without slotting the jamb liner, which we don’t recommend.

To identify your unit, open the sash and look for the etched code in the upper right glass corner, or remove the balance cover and photograph the stamped part number on the spring housing. If the label is gone, measure the visible glass width and height to the nearest 1/8 inch, and note whether the frame is white, almond, or bronze - Atlas used different weatherstrip profiles by color family through 2019.

We source OEM Atlas parts through the manufacturer’s Florida distribution center in Orlando, typically two business days. For same-day fixes, we stock quality aftermarket equivalents from Amesbury and Caldwell that match the critical dimensions and carry the same 10-year finish warranty. The aftermarket balance springs are rated for 15,000 cycles versus Atlas’s 12,000-cycle OEM spec, which matters in West Palm Beach where salt air corrodes the pivot bar faster than inland climates.

Signs Your Atlas Windows & Doors Is Failing

• Sash drops or won’t stay open. The coil balance has lost tension, usually from a fatigued spring or corroded pivot bar. In West Palm Beach, we see this at 8-12 years on east-facing units where morning salt spray collects in the jamb liner.
• Visible gap at the meeting rail when closed. The sash cam lock has worn or the keep has shifted. On Atlas units from 2012-2016, the zinc alloy lock body crystallizes in high heat and cracks before the hardware shows surface rust.
• Condensation between glass panes. The insulated glass unit (IGU) seal has failed, allowing moist Florida air into the airspace. Once fog appears, the Low-E coating is already degrading and the unit needs replacement, not defogging.
• Tilt latch won’t engage or releases on its own. The plastic latch tooth has worn flat or the spring clip has corroded. Atlas used two different latch depths across series; the wrong replacement will seat flush but not catch under load.
• Air infiltration at the sill even when locked. The bulb weatherstrip has compressed or the fin seal has torn at the corners. On Atlas sliding doors, the interlock weatherstrip at the center stile fails first because it takes the pressure of both panels.

Before

After

Replacement Cost & What’s Included

For Atlas window and door part replacement in West Palm Beach, service calls typically run $400-$1,800 depending on what’s failing and how many units are involved. A single balance or lock replacement on a standard double-hung runs $180-$340 in labor plus $45-$120 for the part. Full sash or IGU replacement pushes toward $600-$1,200 per opening because we disassemble the frame, verify square, and reseal with backer rod and silicone compatible with Atlas’s vinyl formulation.

What drives the range: accessibility (second-story requires ladder work), part availability (OEM versus aftermarket), and whether we find secondary damage when we open the frame. We quote a flat written price before any work starts, under Clause 1 of the Haven Standard, with parts and labor itemized. Every Atlas repair carries our 365-Day Done Right Promise, and you receive a documented photo record of the condition we found and the installation we completed.

DIY or Call Us?

An owner can safely check the etched glass code, photograph the part number, and test whether the sash moves freely in the track without forcing it. What goes wrong fast: removing a tilt sash without supporting the balance, which lets the coil snap up into the jamb at speed, or prying a stuck lock and cracking the vinyl rail. Atlas balances are under tension and can cut skin or damage the jamb liner if released improperly.

We don’t recommend homeowner disassembly of impact-rated units because the laminated glass is heavy, the reinforced frame is unforgiving, and the installation documentation must be intact for windstorm insurance credits. If you’re unsure of the series or the part, call us at (561) 475-3903 and we’ll walk through identification before scheduling. Measure twice, document everything, then get out of the way and let the work speak.

FAQs