Tamko Kitchen Remodeling Nationwide

Tamko Kitchen Remodeling: The West Palm Beach Owner’s Guide

Tamko kitchen remodeling in West Palm Beach typically runs $14,000-$45,000 installed, depending on cabinet grade, layout changes, and whether we’re working with original Tamko specs or updating to current KraftMaid or Wellborn lines. We stock measurements and compatibility charts for Tamko’s legacy kitchen product range, and we can usually schedule a site visit within 48 hours. Most West Palm Beach homeowners discover their Tamko kitchen needs attention when cabinet boxes start sagging at the hinge mounts, or when the original laminate countertops show delamination along the front edge where Florida humidity has worked its way into the substrate.

Call (561) 475-3903

Which Tamko Models This Applies To

Tamko manufactured kitchen cabinetry and countertop systems primarily in the 1980s through the mid-2000s under several product lines, including the Builder’s Series, Classic Craft, and later the Heritage Collection. The Builder’s Series used a 3/4-inch particleboard box with thermofoil door fronts; Classic Craft upgraded to plywood boxes with hardwood frames. Heritage introduced soft-close hardware and full-overlay door styles. To identify your line, check the hinge cup bore pattern: Builder’s Series used a 35mm cup with two 5mm mounting holes on a 48mm vertical spacing, while Heritage moved to a 45mm spacing with three holes for heavier doors.

The critical compatibility gotcha in West Palm Beach is drawer glide length. Tamko’s original 18-inch and 21-inch undermount glides were proprietary to their box depth, and standard aftermarket replacements often bind by 3/8 inch. We measure the existing box interior before quoting, because forcing a standard glide into a Tamko box tears out the particleboard sidewall. For countertops, Tamko’s post-formed laminate was built on a 1.5-inch buildup with a 1/8-inch radius edge; modern replacements at that thickness are limited, so we often spec Cambria or Caesarstone at 2cm or 3cm with a custom build-down to maintain backsplash alignment.

Rowan Construction Group West Palm Beach is an independent service provider, not affiliated with Tamko. We source OEM-equivalent hardware from Blum and Grass, and countertop materials from our vetted brand list including KraftMaid, Cambria, and Silestone.

Signs Your Tamko Kitchen Remodeling Is Failing

• Door fronts peeling at the corners. Thermofoil delamination starts where the heat from a toaster oven or dishwasher vent meets the adhesive line. In West Palm Beach, the added humidity accelerates this; once the seam lifts, the MDF core swells and the door is done.
• Drawers sticking or dropping. The original epoxy-coated steel glides lose their ball bearings after 15-20 years of salt-air exposure. We find the bearing races corroded solid in beach-proximity homes from Palm Beach Shores north to Jupiter Inlet.
• Countertop seams darkening or lifting. Laminate seams were bonded with contact cement that degrades with thermal cycling. A dark line at the seam usually means moisture has penetrated to the particleboard substrate, which then expands and pushes the seam further apart.
• Sink cabinet floor sagging or soft. Tamko’s sink bases used a 1/2-inch particleboard floor with a thin melamine face. Drip leaks from the P-trap or spray hose saturate this material; by the time it feels soft, the structural integrity is gone and mold is likely.
• Wall cabinets pulling away from studs. Original installation often used 2-1/2-inch drywall screws into single studs, not the 3-inch cabinet screws into blocking that current code requires. The added weight of stacked dinnerware eventually wins.

Before

After

Replacement Cost & What’s Included

Kitchen remodels in West Palm Beach using Tamko-compatible specifications run $14,000-$45,000, with most projects landing in the $22,000-$32,000 range for a 10×10 kitchen with mid-grade materials. The low end covers cabinet refacing with new doors and drawer fronts on existing Tamko boxes, plus laminate countertop replacement. The high end involves full demo, new KraftMaid or Wellborn cabinets, Cambria or Caesarstone countertops, and layout reconfiguration with permit-drawn plans.

What drives the range: box condition (can we save them or are they moisture-damaged), countertop material (laminate at $2,000-$3,500 versus quartz at $4,500-$6,500), and whether we’re moving plumbing or electrical. Every quote is a flat written price with line-item breakdown: demo, cabinets, countertops, backsplash, plumbing reconnect, electrical, and permit fees. Under Clause 1 of the Haven Standard, that price is fixed; no work proceeds on any change until the change order is signed. Our 365-Day Done Right Promise covers the installation, and we pull all required permits with inspections passed before we close the job.

DIY or Call Us?

There’s safe checking, and there’s work that needs a crew. A homeowner can verify whether a cabinet is particleboard or plywood by removing a hinge and inspecting the bore hole: plywood shows distinct layers, particleboard is uniform and crumbly. You can also measure drawer glide length and count mounting holes. What you shouldn’t do: attempt to remove a bank of upper cabinets solo. They’re heavier than they look, and a 36-inch wall cabinet with dishes inside can exceed 200 pounds. The real risk is stripped screw holes in drywall that let go suddenly.

Demo of a kitchen with possible asbestos in old flooring adhesive, or electrical circuits that need GFCI updating to current Florida code, is not weekend-warrior territory. We bring background-checked, uniformed crews who document every visit with a photo record, included as standard. If you’re weighing whether to patch or replace, call (561) 475-3903 for a free estimate. We’ll inspect the boxes, check for substrate damage, and give you a written price before any work starts.

FAQs