Boral Fence Installation Nationwide

Boral Fence Installation: The West Palm Beach Owner’s Guide

Boral fence installation in West Palm Beach typically runs $3,500-$9,000 for a standard vinyl or aluminum perimeter, with exact pricing set by linear footage, post depth requirements in our sandy coastal soil, and whether we’re tying into an existing Boral gate system. We stock Boral-compatible posts, rails, and pickets for same-day starts on most residential layouts, and we deliver a written price before any post hole is dug. Most homeowners first realize their Boral fence needs attention when a rail pops out of a post pocket after a summer storm, or when the white vinyl starts chalking and the neighbor’s dog finds the gap.

Call (561) 475-3903

Which Boral Models This Applies To

Boral’s fencing line in the Florida market breaks into two main families: the Boral vinyl systems (typically 5-inch square posts with 2-inch by 3.5-inch top and bottom rails) and the Boral aluminum ornamental line (usually 2-inch square posts with 3/4-inch pickets). The vinyl systems carry a date stamp embossed on the underside of the bottom rail; aluminum units have a small laser-etched code inside the post cap channel. If your fence went in between 2012 and 2019, check for the older Boral rail-to-post bracket system - the pocket depth was 1.5 inches, and the current 2-inch pocket rail won’t seat properly without swapping the posts. We carry both profiles on our West Palm Beach trucks because we’ve found that mismatch on at least a dozen jobs south of Okeechobee Boulevard.

OEM Boral parts ship from their southeastern distribution center in Georgia with a 10-14 day lead time. We source equivalent-grade rails and posts from our vetted aftermarket suppliers - same wall thickness (0.055 inch for vinyl, 0.125 inch for aluminum), same UV stabilizer package rated for South Florida exposure - and we warranty the installation under our 365-Day Done Right Promise. If you want OEM, we’ll order it and schedule around the delivery. Most of our customers don’t, once they see the spec sheet side by side.

Signs Your Boral Fence Installation Is Failing

• Rails pull out of post pockets. The Boral pocket-and-rail connection relies on a friction fit plus a hidden screw. After three or four West Palm Beach summers, thermal expansion cycles loosen the grip, and a 60-mph afternoon gust finishes the job. We find this most often on south-facing runs where the PVC hits 140 degrees.
• Post leans at the base. Our sandy soil doesn’t hold a post the way clay would. If the original installer used 24-inch depth instead of 30-inch, or skipped the concrete collar, the post tilts under rail tension. In El Cid and Flamingo Park, we’ve pulled posts that were essentially loose in a hole.
• Chalking or yellowing on white vinyl. The titanium dioxide UV barrier breaks down after 7-10 years of Florida exposure. Once the surface starts to powder when you rub it, the structural layer underneath is next. Gray and tan Boral colors hide it longer; white shows it first.
• Gate sags or latches miss. Boral gates use a steel internal frame with vinyl cladding. The frame welds at the corners fatigue, especially on 6-foot widths with no center support. The latch post shifts, and the gravity latch lands an inch low.
• Picket tops crack at the rail. Boral pickets slot into the rail from the top down. If the rail bowed even slightly during install, the picket carries tension at the slot edge. A palm frond strike or a kid climbing over snaps it clean.

Before

After

Replacement Cost & What’s Included

For a standard Boral fence installation in West Palm Beach, expect $3,500-$9,000 installed. A 150-foot vinyl privacy run with one gate lands around $5,500-$7,000; a 200-foot aluminum picket with two gates pushes toward the upper end. The range moves with post count (we space at 6 feet on center, not 8, for rigidity in our wind zone), soil condition (limestone shelf means auger rental), and whether we’re removing an old fence or working from bare ground.

Every quote is a flat written price with line-item breakdown: materials by the section, posts by the piece, gate hardware kit, haul-away of old fence, and permit if your West Palm Beach property requires one. Under Clause 1 of the Haven Standard, that price is locked before we start. No change order gets signed after the fact unless you add something. Our 365-Day Done Right Promise covers the installation; manufacturer defects on Boral or equivalent materials are handled through our supplier. You’ll get a documented photo record of every post depth, every concrete pour, and every finished gate swing before we leave.

DIY or Call Us?

There’s nothing inherently dangerous about fence work - no high-tension springs, no live electrical - but there are ways to waste money fast. A homeowner can safely walk the line, check for loose screws, and measure post spacing with a tape. What goes wrong: auguring post holes in our sand without a collar form, so the concrete bellies out underground and the post leans by month three. Or setting rails without a grade laser, so the fence follows the yard contour like a roller coaster. Or ordering Boral parts by the “standard” size and discovering your 2016 install used the older pocket profile.

We carry both Boral rail profiles, post brackets, and gate frames on our West Palm Beach trucks. If you want to confirm your part before we come out, text us a photo of the rail end and the post pocket. We’ll tell you what you’ve got. Measure twice, document everything, then get out of the way and let the work speak. Call (561) 475-3903 to schedule your free estimate.

FAQs