PGT Kitchen Remodeling Nationwide

PGT Kitchen Remodeling: The West Palm Beach Owner’s Guide

PGT kitchen remodeling in West Palm Beach typically runs $14,000-$45,000 installed, with most projects in the $18,000-$28,000 range for a mid-size kitchen using PGT windows or doors as part of the renovation. We stock PGT-compatible framing materials, shims, and fasteners for their WinGuard and EnergyVue series, and we can usually begin demolition within 48 hours of a signed agreement. Most homeowners realize something’s wrong when they notice the window or door unit they planned their kitchen around no longer sits square in the rough opening, or when the original contractor’s installation has shifted after three to five Florida wet seasons.

Call (561) 475-3903

Which PGT Models This Applies To

This page covers kitchen remodeling projects where PGT windows or doors are being replaced, upgraded, or integrated into a new layout. The two series we see most in West Palm Beach kitchens are WinGuard aluminum and EnergyVue vinyl, both common in homes built between 2005 and 2020 from El Cid to the neighborhoods off Okeechobee Boulevard.

To identify your unit, check the etched marking in the glass corner or the sticker on the frame edge. You’ll need the series name, the nominal size (like 3040 or 3660), and the DP rating (Design Pressure, typically DP-50 or higher in Palm Beach County). The rough opening matters more than the sash size; PGT units often need 1/2-inch to 3/4-inch of shim space on each side, and older installations sometimes skimped this, which is why the frame binds after a few years of humidity cycling.

We use PGT OEM jambs and sill pans where the existing unit is salvageable, and we source matching profiles from our verified suppliers when the original part has been discontinued. KraftMaid and Wellborn cabinets, which we also install, are spec’d to clear PGT window stools and apron depths so the trim doesn’t fight the countertop overhang.

Rowan Construction Group West Palm Beach is an independent service provider, not affiliated with PGT.

Signs Your PGT Kitchen Remodeling Is Failing

• The window or door frame is out of square with the drywall. In West Palm Beach, the combination of summer humidity and winter dry spells causes wood framing to move while aluminum or vinyl window frames don’t, stressing the fasteners and shims. We find this most often in 1980s ranch renovations where the original builder used non-treated lumber in the header.
• Water staining on the drywall below or beside the unit. Florida’s driving rains find any gap in the sill pan or flashing tape. The PGT unit itself is usually fine; the failure is in the integration between the window and the surrounding structure, which is why we photograph the rough opening before the new unit goes in.
• The sash won’t lock or the multipoint hardware feels gritty. Salt air corrodes the internal mechanisms even on coastal-grade units. If you’re within three miles of the Intracoastal, we spec stainless hardware upgrades that PGT offers but many original installers skipped to save $40 per unit.
• Condensation between the panes. The insulated glass unit (IGU) has lost its seal. In kitchen locations, the heat differential between the cooking zone and the outdoors accelerates this. We replace the IGU rather than the whole frame when the rest of the unit is sound, which saves roughly 40% versus full replacement.
• The kitchen layout no longer functions because the window location limits cabinet depth. This isn’t part failure; it’s design failure. We see it in West Palm Beach condos where a PGT sliding door was installed without considering that a 24-inch cabinet plus a 1-1/2-inch countertop edge needs 26 inches of clear wall. Moving a PGT unit in a remodel requires engineered headers and permit drawings, which we handle start to finish.

Before

After

Replacement Cost & What’s Included

PGT kitchen remodeling in West Palm Beach falls within our standard kitchen remodel range of $14,000-$45,000. A project that keeps the existing footprint and replaces PGT units with like sizes runs toward the lower end. Moving walls, reworking plumbing for an island, or upgrading from vinyl to impact-rated aluminum pushes toward the higher end.

What drives the range: the condition of the existing framing (we open the wall to check), whether the PGT unit is being moved or replaced in place, and the finish level of the cabinets and countertops. Every quote is flat-priced with a written scope. Under Clause 1 of the Haven Standard, that price is delivered before anyone picks up a tool. No change proceeds without a signed change order, which is why our projects finish within a few percent of the number you agreed to.

The 365-Day Done Right Promise applies: if it’s not done right, we make it right. The documented photo record from every visit is included, not optional. You’ll receive it in a binder at project close, same as every project since 2007.

DIY or Call Us?

There’s a short list of checks a homeowner can make safely. Verify the PGT model number from the glass etching. Measure the rough opening from stud to stud and sill to header. Look for obvious water staining or softened drywall. These observations help us prepare, but they don’t constitute a diagnosis.

Where DIY goes wrong: removing a PGT unit without supporting the header above can compromise the structural integrity of the wall, particularly in single-story construction where the roof load bears directly on that header. Reinstalling without proper sill pan integration and flashing tape sequence channels water into the wall cavity, and by the time you see staining, the damage is extensive. The multipoint locking hardware requires precise adjustment; done wrong, the unit won’t seal and the warranty is void.

We’re not going to tell you this is rocket science. It isn’t. But we’ve been called to fix enough homeowner removals in West Palm Beach to know that the two hours of saved labor cost three days of rework. Call (561) 475-3903 and we’ll schedule a free estimate with a written price before any work starts.

FAQs