Barrette Windows & Doors Nationwide

Barrette Windows & Doors: The West Palm Beach Owner’s Guide

We stock and install Barrette-compatible windows and doors in West Palm Beach, with typical installed replacement costs running $4,500-$15,000 for window replacement and $8,000-$25,000 for impact window installation depending on series and opening count. Most Barrette part failures show up first as operational drag - a sash that won’t stay up, a multipoint lock that catches, or weatherstripping that lets Atlantic moisture through during our summer thunderstorms. Homeowners usually notice the problem when the utility bill jumps or when they feel the draft standing near the frame.

Call (561) 475-3903

Which Barrette Models This Applies To

Barrette has manufactured under several series names over the years, and the part you need depends on when your unit was built. The Builder Series, ProSeries, and Elite lines each used different hardware packages - the multipoint locking mechanisms on the Elite series, for instance, won’t retrofit onto a Builder Series frame without modifying the mortise pocket. Check the spacer bar between the glass panes or the hinge-side jamb for a stamped date code and series label; if the label is painted over, measure the overall frame depth and sash thickness - Builder Series runs 2-5/8 inches, ProSeries at 3-1/4 inches, Elite at 3-1/2 inches.

We carry both OEM Barrette hardware and quality aftermarket equivalents from Truth Hardware and Hoppe where the specification matches. The aftermarket route saves 15-25 percent on parts cost without sacrificing function, but we always verify fit against your exact series before quoting - a mismatch on the cam height or backset dimension means the lock won’t engage the keeper properly. Rowan Construction Group West Palm Beach is an independent service provider, not affiliated with Barrette.

Signs Your Barrette Windows & Doors Is Failing

• Sash won’t stay open or slams shut. The balance system - either a coil spring or block-and-tackle mechanism depending on series year - has lost tension. In West Palm Beach’s salt air, corrosion accelerates this; we see it most often in units facing the Intracoastal or within three miles of the coast.
• Visible moisture between glass panes. The insulated glass unit (IGU) seal has failed, allowing humid Florida air to enter the cavity. Once fog appears, the Low-E coating and argon fill are already compromised; the IGU needs replacement, not defogging.
• Multipoint lock handle turns but latches don’t retract. The gearbox inside the lock mechanism has stripped, usually from forcing the handle when the door is misaligned. Continuing to operate it will damage the keeps in the frame.
• Air infiltration at the sill or meeting rail. Compression weatherstripping has flattened or the pile seal has worn away. On east-facing units, UV exposure degrades the fin seal faster - we replace with silicone-treated bulb seals rated for 10-year flex life.
• Frame corner separation or sealant failure. Thermal expansion cycling in South Florida’s heat pulls at mechanically joined corners; welded vinyl frames hold better, but older Barrette units used screw-together construction at the head jamb.

Before

After

Replacement Cost & What’s Included

For Barrette window replacement in West Palm Beach, our installed pricing runs $4,500-$15,000 for standard replacement and $8,000-$25,000 for impact-rated units - the spread reflects opening count, series selection, and whether we’re working with existing Barrette frames or full-frame replacement. Door units, including sliding patio and entry systems with multipoint hardware, typically fall in the upper half of that range due to the locking mechanism complexity.

Every quote itemizes parts, labor, and disposal separately - no lump-sum mystery. We pull permits where required by Palm Beach County and include a written warranty on both workmanship and the installed product. Under Clause 1 of the Haven Standard, that written price is delivered before any work starts; no change proceeds without a signed change order. Our crews are background-checked and uniformed, and every visit includes a documented photo record as standard.

DIY or Call Us?

There’s a short list of checks any owner can do safely: verify the lock is fully engaged before assuming failure, clean debris from the sill track, and confirm the weep holes at the frame bottom aren’t clogged with paint or insect nests - a blocked weep hole traps water and mimics seal failure.

Where DIY goes wrong is in the disassembly. Barrette multipoint locks are under spring tension; releasing the gearbox without supporting the latch bolts can send small parts into the door cavity, and the adjustment screws that set the compression against the weatherstrip are easy to strip. IGU replacement requires specialized setting blocks and vacuum lifting equipment - tempered glass can’t be cut to fit on site. For the part match and install, call (561) 475-3903 and we’ll schedule a free estimate with the exact hardware in hand.

FAQs