CGI Bathroom Remodeling Nationwide

CGI Bathroom Remodeling: The West Palm Beach Owner’s Guide

CGI bathroom remodeling in West Palm Beach typically runs $9,000-$28,000 installed, depending on whether we’re updating a guest bath with stock CGI vanities or reconfiguring a master suite with custom shower enclosures and tile surrounds. We stock CGI-compatible cabinetry, hardware, and fixture rough-ins on our West Palm Beach trucks, and most CGI bathroom remodels we quote can start within two to three weeks of written approval. Homeowners usually discover their CGI bathroom components are failing when cabinet hinges start sagging in the humidity, drawer glides stick from salt air corrosion, or the original particleboard substructure swells after years of Florida’s steam-cycle conditions.

Call (561) 475-3903

Which CGI Models This Applies To

CGI produces several cabinet and bath fixture lines, and the parts are not interchangeable across series. The Builder’s Series uses 3/4-inch overlay hinges with 35mm cup bore, while the Designer Series shifts to full-overlay soft-close hardware with a different mounting pattern. If you’re holding a failed hinge or glide, check the back of the cabinet box for a white or silver label printed with a six-digit SKU and series code beginning with “CGI-B” or “CGI-D.” The mounting hole spacing on Builder’s Series is 45mm center-to-center; Designer Series is 52mm. We carry both OEM CGI hardware and Blum aftermarket equivalents that meet the same cycle-test standards. The aftermarket Blumotion hinges cost about 15% less and carry the same 75-pound door rating, but they void any remaining CGI cabinet warranty if the original is still active. For West Palm Beach homes built between 2015 and 2020, we most often see the Builder’s Series with the original zinc-coated hinge cups, which corrode faster within five miles of the coast than the stainless hardware CGI switched to in 2021.

Signs Your CGI Bathroom Remodeling Is Failing

• Doors hang crooked or won’t stay closed. The original hinge cup loosens its press-fit in the particleboard stile, especially where bathroom exhaust fans are undersized for Florida humidity. We see this in West Palm Beach condos near the Intracoastal where the original 50-CFM fan never met code for the room volume.
• Drawers stick, jerk, or fall off their tracks. CGI’s undermount epoxy-coated slides corrode at the ball bearing race when steam penetrates the lubricant. The drawer box itself often survives; the slide is the failure point.
• Particleboard cabinet sides bulge or delaminate. This happens when the thermofoil or laminate seam at the sink base fails and allows water wicking. In West Palm Beach, we replace more sink-base cabinets than uppers for exactly this reason.
• Sink or tub surround shows gaps at the silicone joint. CGI’s cultured marble and solid-surface surrounds shift with seasonal expansion; the original bead cracks and moisture gets behind. We check for subfloor damage when we quote this.
• Fixture finish flakes or pits. CGI’s earlier chrome and brushed-nickel plating (pre-2019) was rated for interior use but not the salt-air environment of coastal Palm Beach County. The base metal corrodes from underneath.

Before

After

Replacement Cost & What’s Included

The range depends on three factors: whether we’re matching existing CGI components or switching brands, how much water damage exists behind the failed part, and whether the original plumbing rough-in suits the replacement. Every quote we write in West Palm Beach lists parts, labor, and permit costs as separate line items. Under Clause 1 of the Haven Standard, that written price is fixed; no change proceeds without a signed change order. Our 365-Day Done Right Promise covers the installation and any CGI-compatible parts we supply.

DIY or Call Us?

There’s a safe middle ground for homeowners. You can remove a cabinet door and measure the hinge bore and mounting pattern with a tape measure and caliper. You can photograph the SKU label and email it to us. What goes wrong is the install: pressing a 35mm hinge cup into particleboard without a proper jig cracks the stile, and misaligned drawer slides bind within a week. If water damage is behind the cabinet, DIY replacement covers the symptom while the subfloor rots. For cultured marble or solid-surface surrounds, the adhesive sets in three minutes and the piece weighs 80-plus pounds; one slip and the material cracks or the plumbing stub shears. We don’t recommend homeowner removal of glued surrounds. Call (561) 475-3903 and we’ll photograph the failure, measure on site, and give you a written price before any work starts.

FAQs