CGI Kitchen Remodeling Nationwide

CGI Kitchen Remodeling: The West Palm Beach Owner’s Guide

CGI kitchen remodeling in West Palm Beach typically runs $14,000-$45,000 for a full project, with cabinet installation alone at $4,000-$13,000 and countertops at $2,000-$6,500. We stock and install CGI-compatible cabinetry, hardware, and finishing systems, and we carry common CGI door styles and hinge configurations on our trucks for same-day repairs. Most West Palm Beach owners discover their CGI kitchen needs attention when cabinet doors begin sagging, drawers lose their soft-close function, or the laminate veneer starts lifting at the seams after years of Florida humidity cycling.

Call (561) 475-3903

Which CGI Models This Applies To

CGI’s kitchen product line spans several series, and the part you need depends on when your cabinets were manufactured. The Builder Series (2012-2019) used a 35mm cup hinge with a 110-degree opening angle and a proprietary mounting plate that differs from the 2020-plus Designer Series, which switched to a 165-degree soft-close hinge with a clip-on plate. If you’re holding a broken hinge or a cracked drawer front, check the inside edge of the door for a small embossed stamp: “CGI-B” indicates Builder Series, while “CGI-D” or a QR code points to Designer or Premium lines.

We also see a fair number of CGI commercial-grade cabinets that were sold through Florida distributors for multi-family builds around West Palm Beach, particularly in complexes off Okeechobee Boulevard and near Palm Beach Lakes. These units often used a heavier 3/4-inch box construction with metal drawer sides that are no longer in the residential catalog but remain available through our supply chain. For OEM versus aftermarket, we typically recommend staying with CGI-original hinges and slides, the mounting geometry is specific enough that generic hardware often leaves a 1/8-inch gap that grows over time. For decorative panels and toe kicks, a quality aftermarket match from our KraftMaid or Wellborn stock usually saves 20-30 percent with no visible difference once installed.

Signs Your CGI Kitchen Remodeling Is Failing

• Doors hang crooked or won’t stay closed. The 35mm hinge cup has wallowed out in the particleboard door, or the mounting screw holes have stripped. In West Palm Beach, this accelerates when cabinets sit unconditioned during summer vacancy, the wood swells, then contracts, and the screw loses its bite.
• Drawers slam or stick instead of gliding. The soft-close damper has failed, or the ball-bearing slide has corroded from salt air if you’re within a few miles of the Intracoastal. We replace the slide assembly rather than trying to rebuild it, the integrated design doesn’t field-service well.
• Laminate surfaces bubble or peel at the edges. Moisture has breached the edge banding, usually near the sink or dishwasher. Once the substrate swells, the laminate delaminates progressively; patching buys months, not years.
• Shelves bow or clips pull through. CGI’s adjustable shelf system uses a 5mm pin in a metal bracket; overloaded pantries or repeated humidity cycles fatigue the bracket until it tears out of the sidewall.
• Cabinet boxes smell musty or feel soft at the base. The toe-kick area has taken water, often from a slow leak or mopping that pooled underneath. The 3/4-inch particleboard carcass wicks moisture upward, and by the time you smell it, the box floor is compromised.

Before

After

Replacement Cost & What’s Included

What drives the range: access (island cabinets take longer than wall runs), finish grade (painted MDF versus stained hardwood), and whether we’re matching existing CGI in a partial remodel or starting fresh. Under Clause 1 of The Haven Standard, you get a written price before any work starts, every line item listed, and no change proceeds without a signed change order. Our 365-Day Done Right Promise covers the installation and hardware function; manufacturer defects go through CGI’s own warranty channel, which we handle as part of the job.

DIY or Call Us?

There’s a clear line here. An owner can safely tighten a loose hinge screw with a Pozidriv #2 driver, or swap a shelf pin, or photograph a part label and email it to us for identification. What we don’t recommend: removing a wall cabinet solo, the 36-inch uppers in a CGI kitchen run 80-120 pounds once loaded with dishes, and Florida’s older homes often have 1/2-inch drywall with questionable stud spacing. We’ve seen pull-through failures in West Palm Beach condos where the original installer missed the stud entirely and relied on toggle bolts that fatigued over a decade.

Similarly, drawer slide replacement looks simple until you realize CGI’s commercial-grade units used riveted rear brackets that require drilling out and re-riveting, not a screwdriver job. If you’re handy and have a helper, a base cabinet door swap is reasonable weekend work. If you’re dealing with wall cabinets, water damage, or anything that involves the cabinet’s structural attachment to the wall, call (561) 475-3903 and we’ll schedule a free estimate with a written price before anyone picks up a tool.

FAQs